Russ' 1994 Hardtop 2GRFE V6 MR2

Moderators: Administrator, Executive Members, Moderator Group

Re: Russ' Spring MR2 Project

Postby immorality » Sat Jun 11, 2011 8:47 pm

A little update today... the harness has been connected for a couple of days, and I've been trying to sort through it. At first I had a tough time figuring out where everything went, and what all the connector are for. Anyways, that's sorted, and I got my pipe coupling in the mail and I got my intake together, but I still need to bring one of my filters out there are attach it. I got the car to crank over, but it wouldn't start.

I was missing a new coolant temp sensor, so I managed to pick one up today, got back and installed it. Then I bumped the fuel pressure up a bit. It was reading ~44psi, so I upped it to the required 50psi. Then I got in the car, turned the key, and nearly shit my pants as the car roared to life. Let me put the emphasis on ROARED! Open headers FTW!
User avatar
immorality
BCMR2 Web Admin & Executive Board Member
 
Posts: 9730
Joined: Thu Oct 31, 2002 1:32 pm
Location: Burnaby
Status: Offline

Re: Russ' Spring MR2 Project

Postby Saiko » Sun Jun 12, 2011 8:11 am

Nice work Russell!! Glad you didn't shit your pants and that the car is very close to being ready! Can't wait to see it.. in my rear view mirror =)
Eric
92T
Go CANUCKS!!
User avatar
Saiko
Grandfather '2
 
Posts: 1759
Joined: Sun Jul 11, 2004 10:43 pm
Location: Raincouver
Status: Offline

Re: Russ' Spring MR2 Project

Postby immorality » Sun Jun 12, 2011 9:36 am

Thanks Eric! There are still a lot of loose ends to tie up. I'm not sure if I should drive it to the exhaust shop. It's loud at idle, but even part throttle sounds like the end of the world!

Saiko wrote:Can't wait to see it.. in my rear view mirror =)


...only if you're parked! :twisted:

I also have to give a big thank you to Randy, for putting up with me and the car for so long!! Also to Jordan, Sarah, Duncan, Martin and everyone else that had to listen to me talk on about this or that! :BeerChug:
User avatar
immorality
BCMR2 Web Admin & Executive Board Member
 
Posts: 9730
Joined: Thu Oct 31, 2002 1:32 pm
Location: Burnaby
Status: Offline

Re: Russ' Spring MR2 Project

Postby 1992_ST185 » Sun Jun 12, 2011 8:14 pm

YEEEE HAWWWW!!!!!!!!!!!!
DELETE MY ACCOUNT
1992_ST185
Baby '2
 
Posts: 77
Joined: Sun Jul 01, 2007 4:46 pm
Status: Offline

Re: Russ' Spring MR2 Project

Postby Kenisuho » Sun Jun 12, 2011 10:56 pm

haha cant wait to see you release the beast out on the road! Its really nice =D We should all bring their screamers out and drive around the malls in lower mainland and trigger all the alarms in the lots..hahaha
Kenisuho
 
Posts: 14
Joined: Mon Feb 14, 2011 1:11 am
Location: Burnaby
Status: Offline

Re: Russ' Spring MR2 Project

Postby bbarnumboy » Mon Jun 13, 2011 10:21 am

you forgot to make a first startup video
God created turbo lag to give the v8's a brief moment of hope
User avatar
bbarnumboy
MR2 know it all
 
Posts: 3097
Joined: Sat May 06, 2006 12:08 pm
Location: Everett, WA
Status: Offline

Re: Russ' Spring MR2 Project

Postby immorality » Mon Jun 13, 2011 11:03 am

bbarnumboy wrote:you forgot to make a first startup video


There's two very good reasons for that. 1. I don't think my iphone would be able to capture the sounds properly (if at all), and 2. I blew the hose off the oil cooler lines and spewed about 2 liters of oil on the garage floor. I'll see if I can get some video next time I'm out there.
User avatar
immorality
BCMR2 Web Admin & Executive Board Member
 
Posts: 9730
Joined: Thu Oct 31, 2002 1:32 pm
Location: Burnaby
Status: Offline

Re: Russ' Spring MR2 Project

Postby Goopi » Mon Jun 13, 2011 12:14 pm

Congratulations man, hopefully you like the new V6 transplant. :wink:
User avatar
Goopi
Papa '2
 
Posts: 1015
Joined: Fri Nov 13, 2009 1:25 pm
Location: Surrey, B.C
Status: Offline

Re: Russ' Spring MR2 Project

Postby immorality » Sun Jun 19, 2011 6:27 pm

No exhaust yet... and my phone can't take the volume.

User avatar
immorality
BCMR2 Web Admin & Executive Board Member
 
Posts: 9730
Joined: Thu Oct 31, 2002 1:32 pm
Location: Burnaby
Status: Offline

Re: Russ' Spring MR2 Project

Postby LittleDragon » Wed Jun 22, 2011 7:24 pm

come up with a parts list... and let me drive it around the block... lol... I think I've decided on a V6 swap for my restoration project. I just don't know which one... I want low end torque and tall enough gearing for a GT car because I'll be driving it to Vegas quite a bit... lol
User avatar
LittleDragon
Grandfather '2
 
Posts: 1644
Joined: Fri Oct 04, 2002 3:30 pm
Location: Roawr
Status: Offline

Re: Russ' Spring MR2 Project

Postby immorality » Wed Jun 22, 2011 9:22 pm

Well, you don't want an MR2 turbo tranny on it, it will rev way to high for your liking.
User avatar
immorality
BCMR2 Web Admin & Executive Board Member
 
Posts: 9730
Joined: Thu Oct 31, 2002 1:32 pm
Location: Burnaby
Status: Offline

Re: Russ' Spring MR2 Project

Postby bbarnumboy » Wed Jun 22, 2011 9:25 pm

The E153 s supposed to max at like 173 mph on a 3rd gen 3s rev limit. thats not very high reving lol.
God created turbo lag to give the v8's a brief moment of hope
User avatar
bbarnumboy
MR2 know it all
 
Posts: 3097
Joined: Sat May 06, 2006 12:08 pm
Location: Everett, WA
Status: Offline

Re: Russ' Spring MR2 Project

Postby bbarnumboy » Wed Jun 22, 2011 9:29 pm

my facts list.

Gear Ratio / Maximum speed @ 6850rpm redline, stock 205/65 R-15's

3.54 / 40.4mph
2.05 / 69.8mph
1.33 / 107.6mph
1.03 / 138.9mph
0.82 / 174.5mph

So if it can reach 174 mph at 6850 rpm in 5th i would imagine highway cruising should be fairly low?
God created turbo lag to give the v8's a brief moment of hope
User avatar
bbarnumboy
MR2 know it all
 
Posts: 3097
Joined: Sat May 06, 2006 12:08 pm
Location: Everett, WA
Status: Offline

Re: Russ' Spring MR2 Project

Postby immorality » Thu Jun 23, 2011 7:12 am

I'm still trying to get the tach working to verify the speeds & rpm's.
User avatar
immorality
BCMR2 Web Admin & Executive Board Member
 
Posts: 9730
Joined: Thu Oct 31, 2002 1:32 pm
Location: Burnaby
Status: Offline

Re: Russ' Spring MR2 Project

Postby LittleDragon » Thu Jun 23, 2011 10:03 am

Yeah, the 5-6 times I drove to Vegas, its hard to sleep as a passenger when the engine's going over 4000rpm at 80mph. It's kinda why I don't even go to places like Seattle anymore, I can only take the sound for so long
User avatar
LittleDragon
Grandfather '2
 
Posts: 1644
Joined: Fri Oct 04, 2002 3:30 pm
Location: Roawr
Status: Offline

PreviousNext

Return to Members MR2's & Build Threads

Who is online

Users browsing this forum: No registered users and 2 guests